User Tools

Site Tools


linux:legomindstorms

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
linux:legomindstorms [2013/12/31 20:34] rlunarolinux:legomindstorms [2022/12/02 22:02] (current) – external edit 127.0.0.1
Line 68: Line 68:
 </code> </code>
  
-My first step will be to reach the RS232 adapter correctly and get the black box. So, connect your RS232 adapter and the black box and make sure this is on. The "on" in this unit means to move the switch to the biggest triangle: +My first step will be to reach the RS232 adapter correctly and reach the black box. So, connect your RS232 adapter to the black box and make sure this is on, and with the batteries connected. The "on" in this unit means to move the switch to the biggest triangle: 
  
 {{ :linux:20131230_124252.jpg?direct&300 |}} {{ :linux:20131230_124252.jpg?direct&300 |}}
  
-**Next**, turn on the RCX and point it to the black unit, so both can see each other. Remember that the connection is via infrared. +**Optionally**, you can turn on the RCX and point it to the black unit, so both can see each other. Remember that the connection is via infrared. 
  
-**Next**, run the following code: +Now run the following code:
  
 <code shell> <code shell>
Line 80: Line 80:
 </code> </code>
  
-When running it, I've observed no error messages and no ''Could not open serial port or USB device'' message. This is important.+When running it, I've observed no error messages and no ''Could not open serial port or USB device'' message. This is important. When running this command, you should see a green light in the black box during a moment: 
 + 
 + 
 +{{ :linux:20131230_135707.jpg?direct&300 |}} 
  
 **Other commands to test proper running** **Other commands to test proper running**
  
-I've run this command:+You can try other commands that doesn't require to have a program like this:
  
 <code shell> <code shell>
Line 91: Line 95:
 </code> </code>
  
-So I'm afraid further investigation is needed.+==== Install the firmware in the RCX (the yellow box) ====
  
-**Last try**+The next step is installing the firmware in the RCX. There are various firmwares out there, but for NQC we need the official firmware from LEGO.
  
-I've attached a motor to the "C" square of the RCX: 
  
-{{ :linux:20131230_120903.jpg?direct&300 |}}  
  
-And this is my first program:  +===Where is the firmware???===
- +
-<code nqc> +
-task main() +
-+
-    OnFwd( OUT_C ); +
-    Wait( 400 ); +
-    OnRev( OUT_C ); +
-    Wait( 400 );  +
-    Off( OUT_C ); +
- +
-+
- +
-</code> +
- +
-When I try to run it, I get the following error:  +
- +
-<code shell> +
-$ nqc -S/dev/ttyUSB0 -run Hello.nqc  +
-No firmware installed on RCX +
- +
-</code> +
- +
-So, I definitely think that the RCX is completely blank, and I have to install some sort of firmware to have it properly working.  +
- +
-====Where is the firmware???====+
  
 Check out the box of mindstorm: it should be a CD which contains the firmware. To get the firmware from the CD, you should face the following scenarios: Check out the box of mindstorm: it should be a CD which contains the firmware. To get the firmware from the CD, you should face the following scenarios:
Line 132: Line 109:
   - The firmware file is not in the cd, but it is in one of the *cab files. In that case, you can find instruction in this page:[[http://www.17od.com/2013/01/13/using-lego-mindstorms-on-ubuntu/]]. In a nutshell, ''sudo apt-get install unshield'' and then ''unshield x PATH-TO-YOUR-CAB-FILE''.   - The firmware file is not in the cd, but it is in one of the *cab files. In that case, you can find instruction in this page:[[http://www.17od.com/2013/01/13/using-lego-mindstorms-on-ubuntu/]]. In a nutshell, ''sudo apt-get install unshield'' and then ''unshield x PATH-TO-YOUR-CAB-FILE''.
  
-==== Downloading the firmware ====+=== Downloading the firmware ===
  
-In the argot, placing the firmware file in the yellow box (the RCX) is called "download the firmware". I don't know why, because for me is more proper the opposite term (upload), but the terms were set when I came to this world+Placing the firmware file in the yellow box (the RCX) is called "download the firmware". I particularly think that "download" is not the best word for this, but it'the word used everyplace 
  
 Run the following command:  Run the following command: 
Line 168: Line 145:
  
  
-==== Executing the program ====+==== My first program ==== 
 + 
 + 
 +I've attached a motor to the "C" square of the RCX: 
 + 
 +{{ :linux:20131230_120903.jpg?direct&300 |}}  
 + 
 +And this is my first program:  
 + 
 +<code c> 
 +task main() 
 +
 +    OnFwd( OUT_C ); 
 +    Wait( 400 ); 
 +    OnRev( OUT_C ); 
 +    Wait( 400 );  
 +    Off( OUT_C ); 
 + 
 +
 + 
 +</code> 
  
 To run and download the program into the RCX, you should do the following: To run and download the program into the RCX, you should do the following:
Line 183: Line 181:
  
 ===== Second Attempt: LEJOS ===== ===== Second Attempt: LEJOS =====
 +
 +==== Install ant ====
 +
 +You should have ''ant'' installed. To do so, 
 +
 +<code shell>
 +$ sudo apt-get install ant
 +</code>
 +
 +And should have ''libusb-dev'' installed also. 
 +
 +<code shell>
 +sudo apt-get install libusb-dev
 +</code>
 +
 +After doing that, make sure that the usb.h file is available in your destination system. 
 +
 +
 +==== Hands on ====
  
 [[http://www.lejos.org/|Lejos]] is a Java Virtual Machine for the RCX (the yellow box). It's a replacement for the Lego firmware, so, if your CD of mindstorms is broken, it's the perfect solution. [[http://www.lejos.org/|Lejos]] is a Java Virtual Machine for the RCX (the yellow box). It's a replacement for the Lego firmware, so, if your CD of mindstorms is broken, it's the perfect solution.
  
 The web page has a [[http://www.lejos.org/rcx/tutorial/index.html|fantastic tutorial]] that shows the steps to be taken to have this stuff running.  The web page has a [[http://www.lejos.org/rcx/tutorial/index.html|fantastic tutorial]] that shows the steps to be taken to have this stuff running. 
 +
 +When I've checked out the web page, the download link didn't work. But you can go directly to the [[http://sourceforge.net/projects/lejos|sourceforge webpage]] in order to download the files. 
 +
 +When you download and uncompress the file ''leJOS_NXJ_0.9.1beta-3.tar.gz'', you should check out the README.html file. 
 +
 +Then start by setting the environment variable NXJ_HOME: 
 +
 +<code shell>
 +$ cd LEJOS_NXJ_DIRECTORY   # the files ACKNOWLEDGMENTS.txt, LICENSE.txt, RELEASENOTES.txt should be there
 +$ NXJ_HOME=$(pwd)
 +$ export NXJ_HOME
 +</code>
 +
 +Then go to the ''build'' directory and run ''ant''. This is for construct the USB support for java. 
 +
 +In my case, this command failed. The problem was in the ''build.xml'' file located in NXJ_HOME/build/libnxt. I've reconstructed the compiler command: 
 +
 +<code shell>
 +gcc -Wall -std=gnu99 -fPIC main_jlibnxt.c
 +</code>
 +
 +
 +And it fails with this error: 
 +
 +<code>
 +main_jlibnxt.c:28:17: fatal error: usb.h: No such file or directory
 +</code> 
 +
 +**Solution:**
 +
 +    - Locate the usb.h file in your filesystem: ''find / -iname usb.h 2>/dev/null'': in my system this appears in ''/usr/include/usb.h''
 +
 +I've fixed the solution executing the ''make'' command and then:
 +
 +<code shell>
 +$ cd NXJ_HOME/build
 +$ ant
 +</code>
 +
 +
 +
  
  
linux/legomindstorms.1388518468.txt.gz · Last modified: 2022/12/02 22:02 (external edit)